Oxidize! Getting A Vintage Wood Look

Categories DIY Projects163 Comments on Oxidize! Getting A Vintage Wood Look

Update 8/2/19: After receiving hundreds of questions about this topic over the years, I made an updated version over here: Check it out.

When it comes to home decor, vintage is definitely in. But if you have ever done some DIY woodworking projects, you’ll know it can be hard to obtain that aged wood look. You can either buy pricey “barn wood” from a boutique lumber supplier or let your new lumber from Home Depot sit in the backyard, exposed to the elements for a couple of midwest winters – or perhaps you may want to use this easy, inexpensive method for aging your wood in just under a week.

What You’ll Need

For this project you’ll need a few household items from your pantry and garage:

Step 1: Make Your Oxidation Solution

Creating your oxidation solution is straightforward. Take a roll of steel wool and tear off bits into your glass jar. Pour in the vinegar until your jar is full and cap the jar with the lid. Oxidation of the steel wool will take about 4-5 days in my experience. In general, the longer your solution can oxidize, the darker your wood color will be. I tested my solution on some pale pine wood after 3 days and it had a nice dark yellow hue to it. After about 6 days of sitting, the solution produced a dark gray. Because every wood will react differently,  I would recommend testing your solution on scrap wood to see what kind of hue you’ll get.

oxidation solution of steel wool and vinegar sitting on a workbench

Step 2: Give Your Wood Some Tannins

To help give your wood more definition and properly prep it, you’ll want to brush it with some strong black tea. I brewed some rather strong tea with 10 bags in 2 cups of boiling water. As you can imagine, the tea will slightly stain your wood, but it will also give  your wood grain more of a pop. I also discovered that the black tea gives the wood a nicer finisher when you finally apply your oxidation solution. If you skip the tea step, and just use oxidation solution, the wood will end up looking dirty and not aged. There’s just something about that tea that gives the wood a more refined look – sort of how British accents make things seems more sophisticated.

Screen Shot 2016-04-07 at 10.27.33 PM

Step 3: Oxidize Your Wood

When your wood is dry from high tea, and after the oxidation solution has sat for 4-5 days, your wood will be ready to get “the look”. When you crack open (not literally) your jar, there will probably still be steel wool floating in the solution – that’s ok. If you leave the solution sitting long enough, eventually all steel wool remnants will dissolve. And you can save the solution for future projects. Using a foam brush, paint on the solution. The wood will almost instantly turn gray, and over the next 10 minutes, it will get even darker.

use a foam brush to apply oxidation solution to bare wood

Step 4: Sand & Finish

After the wood has dried, give it a light sanding with 400-grit sandpaper. This will help lighten up the stain and even out the color. The more you sand the wood, the more you’ll remove the stain (obviously), but it can produce some unique variations in the grain – up to you, but again, be sure to experiment on some scrap wood before applying to your final project.

For the finish, I use a clear semi-gloss Poly Whey Furniture Finish from Vermont Natural Coatings. This is a really easy-to-use finish with low odor, quick dry time, and it feels great to the touch. I can’t recommend it highly enough, and you have it shipped right to you from Amazon. I like to lightly sand with 400-grit sandpaper after each coat to keep that super smooth feel, and I would recommend applying 3 coats of this finish. Be aware that the finish will change the color of the wood slightly to give it a warmer, almost tarnished hue.

Below is a side-by-side of how far we’ve come with the unfinished pinewood (left) to wood with the tea-stain and oxidation solution (middle) to the wood with 3 coats of finish.

three phases of project: bare wood, wood with oxidation solution, wood with polyurethane finish
before and after: bare pine wood on left and dark, oxidized wood on right

So what will you build now that you know how easy it is to get this vintage wood look? I’ve got a few projects up my sleeve, and when you think about it, the sky’s the limit. Imagine building your own farm table or a little box for holding those bathroom towels that you’re not suppose to use – whatever! Below is a wall-mount bottle open I made. My goal was to make it look like the plank of wood came from an old crate from the brewery.

wall-mount bottle opener with oxidized wood plank

Let me know if you have any ideas in the comments below, and I would love to see what you build.

And a special thank to Hillary at Friendly Home for all the inspiration for his post.

Published by gadgetsandgrain

I make videos about my little DIY projects.

163 thoughts on “Oxidize! Getting A Vintage Wood Look”

  2. Any idea how this would work on Burma Teak? I’m about to try on a sample anyways. Also, if you’ve tried this on any veneered plywood. Thank you.

    Like

    Reply

    2. Would this work for an exterior wood? I want an aged gray look, but don’t want to wait. Is this actually a stain or is the wood really oxidizing? Thanks!

      Like

      Reply

      1. Hi Claire. This would work on almost any bare wood – the look will just depend on the wood species (i.e. pine, redwood, cedar, etc.). You’ll want to make sure to apply a finish on top of the stain to protect it. And yes – this is really oxidizing the wood by speeding up the chemical reaction that naturally happens over time.

        Like

      1. Heat the vinegar for 5 mins in microwave then add wool. It will be ready in 24hours instead of waiting a week. Can add a teaspoon of hydrogen peroxide the next day if you want it dark dark.

        Like

  5. Pingback: Large Antique Pine Storage Bench / Settle c.1900 – Pinefinders Old Pine Furniture Warehouse | Furniture Idea

  6. Thank you for the great video. …❤️ your little helper!!!
    I tried the vinegar solution (no tea) and my chairs are dark…
    please let me know how to make them a lighter colour ( grey with golden wood tones)
    It takes for ever to sand them and still a very light grey colour remains.
    Any easy technique besides sanding? Thank you…😊

    Like

    Reply

  8. Thanks for the awesome advice! We’ve just had pine decking and sleeper seats installed in our pool area. I wanted pine (or cypress, but no luck) so it could fade to grey. Being the impatient soul that I am, I decided to find out if I could speed up the process. Am definitely going to give your method a try. I have one question: the pine I have is H3 treated, so it has a slight green tinge (which I know will fade), but will your method work, do you know. I have offcuts, so I’ll give it a whirl, but thought maybe you had some experience with treated pine.

    Like

    Reply

      1. Back again. Tried it on two batches of treated pine. One section had the green/bluish tint associated with treated pine and the other section was treated but did not have any colour apart from natural pine. The tannin/ferric acid mix (guessing that’s what steel wool dissolved in vinegar actually is – sounds posh, anyway) worked a treat on both. The green/blue pine still has that colour coming through the dark finish – you can tell the two areas apart merely by their respective colours. Am thinking another coat or two and it might be a better match. Thanks for this idea – it really works, is so simple to do and comes up a treat. Having tried it on a small area, I’m now game enough to go big – pool-side seating – 400mm high hob wall with treated pine ‘sleepers’ along the top.

        Like

  9. Hello, I’m going to attempt this on my new $2500 front door. I’m going to try it on a bit of the matching molding of the same wood type first. I was wondering if you could shoot me your email address so I can send you a picture of the door and get any quick bits of advice you may have. Much appreciated!

    Like

    Reply

  10. Jeremy
    I was wondering what kind of tea did you use? I’m building and enterainment center for my daughter and she wants the deck where the TV sets to have that old weathered look. The deck is red oak.
    Is there a way to control how dark of a gray it takes on?

    Like

    Reply

    1. Hi David. I used black tea, and you try to control how dark the wood gets by adding different amounts of steel wool. The more steel wool in the solution, the darker the stain. You can also sand the wood after the stain to lighten the color. Good luck and shoot me a picture of the project when it’s finished.

      Like

      Reply

  12. Hello ! what a fantastic video !! I came here from youtube and also asked you a question there as well 🙂 Is this a permanent stain ? or will it lighten with time ? I am thinking of applying this method to my lathe turned pens. do you think It would be fine ? Thanks !

    Like

    Reply

  13. Jeremy ~
    Love the info here. My husband and I are remodeling 2 upstairs bedrooms. We plan to have a pine wood ceiling and 2 pine wood accent walls. We’ll be using your method to stain.
    I plan to do some with tea (gray tone), some with coffee (brown tone) and some with only the vinegar solution (light gray). I’m hoping for a variety of tones to then alternate the boards for a slightly uneven, weather wood look.
    Any other suggestions for varying the tones?
    I appreciate your straight forward video, written directions then the follow up here.
    Thank you.
    Molly

    Like

    Reply

  14. I would like to try this on 3/8 inch plywood. The idea is to create a ship lap wall with browns and grays. Your using solid wood boards. Can you get the same effect with one side good plywood?? And thanks again for your video. Very cool.

    Like

    Reply

  15. I want to try this on 11/32 plywood. Going to shiplap a wall. Do I need to presand the plywood strips first. Any suggestions?

    Like

    Reply

    1. If you’re using good quality plywood, you shouldn’t have to sand them before applying the stain. Since plywood can react differently than milled boards, try testing the stain first. Good luck and shoot me a photo of the project when it’s done.

      Like

      Reply

  16. Thanks for the excellent video titled: Oxidize! Getting A Vintage Wood Look. Your video and detailed instructions has inspired me to attempt this process on white pine boards I’m using for bookshelves. I’ll let know how it turns out.

    Like

    Reply

  17. Great tutorial, I think the step with the tea is what all the others are missing. Going to try this out on some projects this week. How did you get the print on those bottle opener boards? Very cool.

    Like

    Reply

  18. Hi, this is the exact look i am wanting for my bath cabinets. I attempted using a gray gel stain, as many websites suggested, but it did not turn out right. If i sand them down, do you think this would work?

    Like

    Reply

    1. Hi Ash. It really depends on the type of wood your cabinets are made out of – would you happen to know? You can try to sand down a small, inconspicuous spot on your cabinets and test it.

      Like

      Reply

  19. I used a propane torch to pop color around knots first, then followed your procedure….worked great on pine. I will be doing it again soon

    Like

    Reply

  20. Distilled white vinegar? It seems after 30 minutes its wanting to pop the top off. Should i leave the lid loose?

    Like

    Reply

  21. Hello thank you for your effort’s in sharing this information I am currently finishing a 10 foot five 4 1/4 foot yellow pine farmhouse table my question is have you every tried this method on a large area my concern would obviously be consistency And volume

    Like

    Reply

    1. Hey Vinny. I haven’t tried this on really large projects like a table. Because this a chemical process for staining, the end result can vary even if you’re using the same species of wood. But some folks like having a varied look – it gives the project some character. If you want to try this, first, test it some scrap yellow pine. And as far as producing enough solution for a large project like your table, you’ll probably be fine with using 1 bundle of steel wool with 16 oz of vinegar. Hope that helps. Good luck!

      Like

      Reply

  22. Hi, I really enjoy your videos, which are full of wonderful ideas, but having tried the steel wool and vinegar technique last week, I thought I should post a word of warning – my jar containing the steel wool and vinegar exploded violently, sending glass and vinegar flying into every part of the kitchen. If someone had been in the kitchen at the time of the explosion they would certainly have been seriously injured. The wooden counters and parts of the floor are now indelibly stained with a thousand black splodges from the vinegar and steel wool, but I’m just grateful that nobody was hurt. I thought maybe you could give more detailed information on the do’s and dont’s of combining steel wool and vinegar, as it is a potentially dangerous combination.
    All the best, and thanks again for all the great videos.

    Like

    Reply

      1. Yes, the jar was sealed – the lid was on too securely. I hadn’t realised that there would be such a build up of gas, and of course, gas needs to escape. Anyway, I think I’ll give it another try now.

        Like

    1. Hey Steven. I’m not sure. Since #0 is not as fine as #0000, it will not dissolve as fast in the vinegar and will give you a solution that produces a lighter color – that’s just my guess.

      Like

      Reply

  24. For some reason my stain has always came out brown after the tea and one coat of oxidation. Any idea why is that? Really looking to get that grey coat.

    Like

    Reply

  25. Love the project idea. Followed everything so far and I just did the steel wool/vinegar solution (sat for 5+ days). Wood is drying but it’s all blotchy and not looking like yours does. Very worried. Any suggestions?

    Like

    Reply

  26. Hi! So the finished product is the far-right bored? I noticed that it is more Brown than grey. That is the look I’m going for. Did you accomplish that by using that specific finish? Or will a different finish do the same thing ?

    Like

    Reply
  27. Pingback: How To Oxidize (And Age) Wood In A Matter Of Minutes – Gadgets and Grain

Leave a Reply

Fill in your details below or click an icon to log in:

Gravatar
WordPress.com Logo

You are commenting using your WordPress.com account. ( Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. ( Log Out /  Change )

Cancel

Connecting to %s