DIY Mobile & Modular Workbench To Bring Your Shop to the Next Level

Categories DIY Projects161 Comments on DIY Mobile & Modular Workbench To Bring Your Shop to the Next Level

Updated 11/28/18 – After receiving some great feedback in the comments section, I have added detailed plans and a cut list for all the boards used in the basic workbench. Let me know if you need anything else.

I tirelessly searched YouTube and Pinterest for workbench designs, and after taking into account the tools I have and the types of project I work on, there were essentially three main features I needed:

  1. Mobility – Hauling tools in and out of a garage is tiring and it eats up time during a build. Plus, if you’re like me, your garage is not quite a full-time woodshop, so being able to store a workbench to the side is a must.
  2. Size – I needed a workbench that could accommodate the largest material I might find myself working with: a 4’x8′ sheet of plywood. It takes a large workbench to act as a decent out-feed table for a table saw or to provide an adequate work area when assembling larger projects.
  3. Modular – A good workbench should be able to change with your needs, so I designed this workbench to either be two smaller halves or one big work area. I also built-in a slot to accommodate a variety of fixed tools such as a miter saw, pocket hole jig, router table, etc.

Before I start with the instructions, I have to give credit to Steve Ramsey at Woodworking for Mere Mortals and Bob at I Like to Make Stuff for the inspiration behind this design. I love the simplicity of Steve’s workbench, and the genius use of magnets with Bob’s work tables . I highly recommend checking out their videos (and their YouTube channels).

Workbench Plans & Cut List

Here are the measurements that I used to build the workbench you see in the video, but by all means, use these as a reference point to build your own bench. Perhaps you’ll want to tae your bench shorter, taller or longer – just tweak the respective measurement to suit your needs.

Workbench Frames

detailed plans for a mobile modular workbench

Workbench Tops, Side and Bottom Shelves

detailed plans for mobile workbenchCut List

cut list for workbench

Workbench Shopping List

Skip this part if you already have everything you need of this project, but if you would like a little help stocking up or some ideas for new equipment, below are links to the tools, materials and supplies used in this video. Just a heads up that I get a small commission from these links, so any support is much appreciated.

Tools & Equipment

Supplies & Materials

Step-by-step Instructions

1. Build the Workbench Frame

The frame of the workbench is comprised of 2×4 and 2×6 boards. I used 2×6 boards for the ends of the frame to add extra stability to the workbench, and also to create deep recesses for shelves for storing tools, cans of finish, clamps, etc. The overall height of the workbench is about about 36-inches, so take into account the thickness of the tabletop, height of the casters, and the cut boards for the frame accordingly. As pictured below, using a stop-block makes cutting consistent lengths much easier.

Cutting legs of the workbench with a miter saw

I used pocket hole joinery to assemble the entire frame. To do this, you will need a pocket hole jig to crank through the many, many pocket holes that need to be drilled. Pictured below is a Kreg K4 pocket hole jig which makes this whole process much easier. It also has a handy attachment for a shopvac to keep the work area clear and the drill bit cool.

Drilling pocket holes for workbench joints

With all the pocket holes drilled, join the frame with 2 1/2-inch Kreg pocket holes screws. Be sure to clamps the boards together while joining them.

Joining workbench frame with pocket screws

The frame is essentially comprised of two long sides while being joined with shorter boards that span the width of the table.

assembling workbench frame
attaching short stretchers to workbench with pocket screws
assembling workbench frame

Once the frame for both benches were assembled, I added a 2×6 to the outside of each side to create the “legs” for the workbenches. This adds extra rigidity to the frame and creates a wider base for attaching casters at the bottom of each workbench. Note that the length of the extra 2×6 is the entire height of the workbench.

attaching 2 by 6 board to reinforce workbench leg
workbench frames assembled, side by side

Once the legs are fully in place, add casters to the bottom of the bench. This makes moving the project much easier as you continue to build it. Use locking casters so the workbench will stay in place when the time calls for it.

screwing on rotating casters to the bottom of the workbench

I caught this later in the build, and the issue is unique to this workbench design where two casters sit next each other, but you’ll have to account for their rotation range. Initially, I had the two inside casters sitting next to each other, and because of this, they would bind up and block one or both from moving freely. This results in a workbench that is very difficult to move and maneuver.

rotating casters on the bottom of the workbench

To correct this, I moved the casters further apart. This lets them rotate freely while the workbench is pushed around. This also added to the height of the workbench.

rotating casters on the bottom of the workbench

2. Build and Attach the Workbench Top

Most of the workbenches I saw online were constructed with top made of 2×4 glued together by their face grain. This makes for a super-strong work surface, but it used quite a bit of material, takes more time and can be challenging to ensure that it’s completely flat. Instead, I opted for 3/4-inch cabinet-grade plywood. I made the top strong by lamenting two layers with glue.

To create the bench top, start by cutting the plywood sheets right up the middle with a circular saw or table saw. Using the Kreg RipCut (pictured below), I was able to make long, straight cuts.

cutting plywood for the workbench top

Laminating these layers of plywood will create a very sturdy and strong work surface, and it starts by liberally brushing on wood glue to one layer of plywood and then placing the other on top of it. To provide clamping pressure while the glue dries, attach brad nails while pressing down on the plywood layers. Be sure to make sure the edges of the plywood line properly.

lamenting the plywood bench top with wood glue
attaching bench top with brad nails

To attached the table top, I drilled pocket holes on the inside of the workbench frame. You can chose to attach the top by simply using screws through the top of the bench top, but that means screw heads will be visible on the workbench. That’s not a huge deal for most, but since I have a pocket hole jig, (in this case a Kreg Mini Picket Hole Jig) I used pocket screws to attach the table top. Whatever you decide to do, be sure to attach the top in a way that allows you to easily remove it down the road in case it needs to be replaced. This workbench is going to get plenty of use and abuse so you can image that the top will need to be replaced at some point in time.

attaching workbench top to frame with pocket screws

3. Attaching the Tables With Magnets

Using the of idea of attaching modular workbenches with magnets, I drilled circular slots into 3-inch strips of pine using a forstner drill bit. These slots fit the circular neodymium magnets that would help clamp the workbenches together.

drilling hole in workbench edging with forstner bit
installing magnets into workbench edging

The wood strips that hold the magnets are wider than the actual thickness of the plywood top. I did this for two reasons: 1) The magnets are wider that then thickness of the workbench, and it was easier to drill the slots on separate pieces of wood than attached them directly to the plywood top. 2) With the top edges of the pine strips flush with the plywood table top, this left a slight over-hang that acted as a handle all the way around the bench top, and moving the workbench became much easier.

gripping the workbench edging

As I mentioned in the build video, it’s recommended to have the magnets stick out a bit from pine board edging. This allows the magnets to make better contact and form a tighter bond when moving both workbenches together. I highly recommend these neodymium magnets on Amazon. I ended up using 6 pairs to attach my workbenches, and I  would maybe even recommend using 8 pairs to make an even tighter bond.

4. Completing the Miter Saw (or Multi-tool) Slot

Of all the features of the workbench, this is the one I have found to be most handy. Turning the workbench into a miter saw station is so convenient, and fortunately, making a small variation to this basic frame design allows you to build this in.

One of the workbench halves has a 3 1/2-inch-deep slot built-in to accommodate a drop-in for a miter saw. This requires additional framing, but the design is simple enough. The boards are 2x4s joined by pocket screws. It just worked out that the height of my miter saw’s work surface is 3 1/2 inches. Carefully measure the dimensions of any tool you want to “drop-in”, and remember to account for the additional height of a table top that will be added later to the workbench.

installing frame in the workbench for the miter saw insert

For times when I didn’t need my miter saw in the drop-in and/or I wanted a completely flat work surface, I created an insert for the drop-in.

2 by 4 frame for the miter saw insert

Before I made the platform for the miter saw, I first made the insert of the slot using 2x4s and two laminated layers of plywood. I build this so the insert would be level with the rest of the workbench. I also used magnets (the same ones used to connect thee sides of the two workbenches) to secure the insert on to the workbench frame.

building the miter saw insert

For the miter saw insert, I also used two layers of 3/4-inch plywood, laminated together with glue, and secured it to the workbench frame with magnets.

installing magnets in the bottom of the miter saw insert

I carefully lined up my miter saw to make sure it was in the center of the insert. If you have a compound miter saw, be sure to test its rotational range in all configurations to make sure the insert will accommodate it. The last thing you want is to attempt to adjust your miter saw for 45-degree cut, only to have it not fully rotate because the workbench slot is not wide enough. With the saw is set in place, attach it to the plywood insert with screws. My miter saw has 4 screw holes for this purpose, but you may need some washers to completely attach yours.

attaching the miter saw to the workbench insert

5. Finishing Touches

You may want to consider applying a few coats of finish on the workbench tops to provide an extra level of durability. This also leaves the workbench feeling silky-smooth, and it makes clean-up a little easier. I also added my logo to the center of the workbench using my trusty inkjet-to-waxpaper transfer method.

applying polyurethane finish to workbench top

Final Thoughts

I am so happy with this design, and I hope this was helpful for as you plan to build your own workbench. I spent a long time sketching this plan on paper, but after actually using this workbench design for 5 months, here are the top aspects that for me:

  • Setting up for woodworking is so much easier when all my tools are on a rolling workstation. I would spend a good 20-30 minutes getting out all the tools I needed for a project, and now this is down to a matter of seconds.
  • The miter saw insert is big a time-saver. Also, since the workbench top is level with the miter saw platform, cutting long boards is much easier. And when I’m not using the miter saw, I can easily store it under the workbench and re-gain a large, flat work area.
  • Having a workbench also creates a lot more storage for your shop. So as you’re working on your design, think about the tools and materials that you want to store.
  • I thought that I always wanted a giant workbench that would sit in the middle of my garage – I mean workshop. But given my set-up, that’s just not practical. Most of the time, there is a car parked in my garage, so splitting the workbench into two lets me store it out of the way. Also, it’s nice to have two smaller workbenches at times, depending on the kind of work I’m doing.
extra storage for screws and tools made out of plywood shelves
Side view of mobile workbench with shelves and storage
using miter saw in the workbench
workbenches stored in the corner of the garage

So what do you think of this design? I’d love to hear your thoughts and suggestions I how to improve it. And let me know if you build one of your own – I love seeing photos of your projects. I’m happy to answer any questions and don’t forget to subscribe to Gadgets and Grain on YouTube.

Links to Tools I Used

If you’re curious about some of the products I used on this project, check them out on Amazon. When you click on the links below, Gadgets and Grain gets a little commission when you check out – I would greatly appreciate it!

storyboard of DIY workbench build

Published by gadgetsandgrain

I make videos about my little DIY projects.

161 thoughts on “DIY Mobile & Modular Workbench To Bring Your Shop to the Next Level”

  1. Your diy modular work bench gets 2 thumbs up from me. For a while now I have been searching for a work bench to build and this is the one. Thanks for sharing it.

    Like

    Reply

    2. Fantastic work bench. I noticed it’s 7.5ft wide. Wouldn’t it have easier to keep it at 8ft wide for fewer cuts. Was there a specific reason you shortened it a bit? Thanks.

      Like

      Reply

      1. Yes – I had in my mind that I would line up these benches end-to-end in my garage, and I have a 15-foot space that would accommodate that. It ended up that I store these benches in a different configuration, and I could have just gone with the 8-foot length – oh well.

        Like

    3. I would love to build your workbench. do you have dimensions of all lumber used and I want to build a shelf to mount my table saw to end of workbench tabletop. Thank You.

      Like

      Reply

  3. I think this is a great setup, perfect to make use of my garage space. Do you have any downloadable plans for this bench that you could share?

    Like

    Reply

  4. I think that your workbench design is awesome. Just one thought is to also use it as an out feed table for the table saw. I don’t think it would be too difficult to incorporate it in your design. Also do you have a material list and a cut list?

    Like

    Reply
  5. Pingback: DIY Wall Mount Workbench – Build a Workshop #54 | Battery Finder

  6. What are the dimensions of this? I’ve cut my 2×6 for centers but did you do 2” or 3”

    Like

    Reply

  8. This is by far the best looking design and functionality that I have seen in a workbench. Any chance you could provide a link for the neodymium magnets. I would like to build one for my shop and I’m shopping for the hardware parts before I start. Thanks.

    Like

    Reply

  11. I totally love this workbench! And your video is awesome! Your design gave me an idea I’d like to share. I’ve never done this so can’t claim it really works but if you or anyone else is interested, you might give it a try. You have made your bench with modular parts. Why not add another part? Do you ever work with bench dogs? If so, you could make another component that included two pieces of 3/4″ ply cut to the same size. One piece, the bottom, would remain solid; the top piece would be the one with the dog holes cut thru it. The top is then glued to the bottom. It could be made the full size of one of your bench modules. Using magnets, recess the washer portion on, say, the 4 corners of your bench top so that the washer is flush with the bench surface. Attach the magnet to the under side of the bench dog component at its 4 corners with the magnets protruding slightly, just enough to make contact with the washers. That way you wouldn’t have to clamp your bench dog surface to your bench, freeing up your clamps for your work piece. When the bench dog addition was not in use, you could hang it on your wall on hooks screwed into the studs. Just drill maybe 3 holes all the way thru your bench dog component stud distance apart. Just a thought.

    Like

    Reply

  12. Fantastic idea and build. Would you be willing to share all the measurements and cuts you used to replicate what you did?

    Like

    Reply

  14. Very good job, this looks like it would be a good fit for my garage.
    Do you have overall dimensions and a cut list availabel?

    Thank you,
    Scott

    Like

    Reply

  15. I love this design. Great functionality. Would you happen to have a breakdown of the total materials and/or the cuts you made? I am an amateur wood worker and I am having difficulty figuring out all you did for the frame. I mainly want to make sure I am able to duplicate the height so I can park my table saw next to it.

    Like

    Reply

  16. Love the design. It is simple but very functional. Would like the dimensions or cut list so to speak. Would make a couple of minor changes like the storage for the miter saw would be on a rolling shelf to make it easier to get in and out.

    Like

    Reply

  17. Wow! This is crazy I sketched up a design very, very similar to this just a couple days ago. Mine has hinges between the two halves, but I like the magnet idea. I might change things up to use that idea. Nice write up and video. Thanks!

    Like

    Reply

  18. This is an awesome bench! I’ve been searching and building the perfect bench, “in my mind anyway “, and this one fits right in. I love the modular miter station. I want mine to also have an end station for my portable table saw. Great job!

    Like

    Reply

  20. Great design for a workbench and it looks like it would suit the space I have. Would you happen to have a cut last for the materials?

    Like

    Reply

  21. This is an awesome workbench, and exactly what I’ve been looking to build for my garage shop. Any chance you have a material list and dimensions you could post?

    Like

    Reply

  22. Jeremy. I really like your design. I looked at the other ones your referenced, and really like Paulk’s too…but I don’t really need a portable system, as I will only use my table at home. I did like the way Paul made a way to attach a table saw at the end of his bench. Do you have plans available for the rolling base?

    Like

    Reply

  27. This looks great, do you have a list of the boards and their measurements, this is a lot of wood but no dimensions. I take they are 24″ wide and 8′ long, but the 2 X 4 and 2 X 6 dimensions is what I am after. This would work great in my garage due to space.

    Like

    Reply

  29. Very well written article with full information. Thank you for sharing this great info. It’s nice to know and read about this stuff. I would definitely try to follow these suggestions.

    Like

    Reply

  31. What a great design! I searched the Internet over and couldn’t find anything like your table. Very nice job!!! I too need my garage for other things as well. Any chance you might have a cut list for this table laying around or was it all done as you built it?

    Like

    Reply

    1. Hey Eddie. Thanks for the feedback, and sorry it took so long to reply to you. I just updated the blog post to include plans and a cut list. Let me know if you run into any questions along the way.

      Like

      Reply

  35. Great build!! I’ve been watching your channel and the modular benches you referenced by Bob at ILTMS. This is pretty close to what I’ve been trying to design, with almost the exact same garage layout and needs. Do you think I could swap out the Miter insert for a flip top? I have to work out the dimensions with the pull saw slide rails and inserting stop block channels on the top.

    Like

    Reply

  37. Great looking table and awesome video. I was wondering if you have a materials list available for the lumber you used. I’d like to give this a shot this weekend, but I’m new to the hobby and not quite sure what to buy when i gey down to the local limber yard

    Like

    Reply

  41. is there a cut list for this workbench as I will have to take the cost list to a place that’s got timber & will have to get the to cut it for me there than I’ll be able to put it together when I get home ( Don’t Drive) so I’ll have to get a uber or a taxi to get the timber home from the timber yard

    Like

    Reply

  42. Hello!! This is a great idea my husband and I would like to try and build. Do you happen to have a shopping list for the materials needed for the project?

    Like

    Reply

  43. Hi. Love the video and the article is exceptional. I am looking forward to building this, as I am in desperate need for a work area. Do you have a materials and cut list?

    Like

    Reply

  45. Love the design, and I plan to use it for my bench. Thanks so much for sharing! One addition I’d suggest is adding a tool box latch to lock the two tables together. Maybe it’s overkill, but you mentioned you might add a couple of more magnets for a tighter bond, maybe the latches along with the 6 magnets would assure tightness.

    Like

    Reply

  48. Awesome design! I may have missed it, but what are the demensions of each bench? I believe length is 7.5, height 36” but did not see a width.

    Thanks!

    Like

    Reply

  50. Great job! I was thinking of something similar to remodel my kitchen, but I have no garage… I would make it between 2 rooms INSIDE the house and cut out areas for a Bosch table saw, either at one end (notches in both halves to set the saw down in) or maybe near the middle to use it as infeed & outfeed tables, though I’d have to figure a way to reach the power, fence and tilt… maybe make one side broken into 2 halves with magnets… Maybe make both sides break apart into halves to make the entire bench into quarters…

    Like

    Reply

Leave a reply to gadgetsandgrain Cancel reply